วันอาทิตย์ที่ 7 สิงหาคม พ.ศ. 2554

How to build your own waterfall DIY – Basics of Pump, Heating and Waterway

How to build your own waterfall DIY – Basics of Pump, Heating and Waterway

How to build your own waterfall DIY – Basics of Pump, Heating and Waterway

Posted: 07 Aug 2011 05:20 PM PDT

Presser Feet

Build your own waterfall can be a rewarding experience, however, the use of water can be difficult, so that as much information as possible, must arm for something you love to build with.

Minimum flows

For each inch of width of the waterfall, you should provide a minimum of 100-150 GPH (gallons per hour) of water through the pump as a waterfall. If you want the upper bowl are chained with a 10-inch wide areawhere the water flows over the waterfall, you need a pump capable of providing 1000gph. You also need to understand how the pumps are classified to ensure that the desired effect you are trying to achieve. It is a loss of efficiency in the movement of water through the pipes and you must take this into account, to ensure that your waterfalls water, ideal flow.

Reviews of pumping and pressure drop

The maximum load for your pump 1000gph saying, refers to a pump at zero pressure head. Head pressure refers to the weight of the water pump and lifting capacity. When the pump to lift water a long way, you produce less than an hour. In simple terms, the pump with a rating that the amount of vertical climb, the need for water, of which. It provides a table of specifications of the pump, the zero pressure head Member hour, but they also expect the gph with one foot of vertical lift, or two> Feet of vertical lift, or five feet high, and so on.

Fittings cause loss of pressure and

Another factor in this equation is frames-angle of ninety degrees, 45 degrees, and the bends in the hose or valves will also increase the pressure head. A pump must lift the water with one foot, but also by a series of four or five 90-degree bend is much less of a pump gph slide with a straighttube.

The height and width of your waterfall to determine the requirements of the pump

For this reason it is necessary to determine the height to reach the water pump needs to push the top shell and also how much you want to have the overflow in the bowl at the top. This will give you an idea of ​​what size pump you need. Suppose, to achieve the same overflow 10 inches wide and five feet vertical climb to the top shell, you need a pump capable of producing a minimum of1000gph with a header from five meters. This means that the label on the pump probably around 1250 gph with reference to the zero-pressure stage manager for the pump with a capacity of over five meters 1000gph head.

Prevalence calculation mounting

We recommend that you consider fittings, bends and restrictions in the bathroom to make it out of the pond until your bowl to the top alsoIncrease in lift. Being used in large applications, the number of elbows, fittings and length of all calculated to determine the exact pressure loss for water to reach its goal. For smaller applications, such as your waterfall of this calculation is not required. When you create the plumbing in your pond to search for the top edge of the waterfall, use as few fittings and elbows as reasonably possible. Especially try to avoid being Fittings, back to back like twoninety degrees or three turns in a short section of pipe. Fittings and bends in quick succession, because the pressure is distributed over the head that the same number of taps further. For simplicity does not calculate the number of connections is used to want to build your waterfall, but the pump is large in size from a minimum of ten percent.

Now the whole equation with health

If you have a waterfall 10 inches and a stroke of five feet, and you make 10%lost in the race for additional flow faucets and pipes, the following conclusions.

1000gph at a pressure head of five feet, is a pump with higher capacity, as 1250gph be applied, always referring to the zero head. To take account of your taps, it would be increased to 10% more, or assessed as a further 125 gph for 1250 gph pump. This means that the minimum power of the pump would you be 1375 gph. Around this number to 1400 orperhaps as a 1500 rating gph pumps are usually sold in increments of flow and probably will not find a pump to 1375 per hour.

The reason why you should consider at this stage because it is necessary to determine the size of the pipe, you must run the module from the pond waterfall tip the bowl. If you liked the flow that is needed to assess the extent of the water where it is expected you can find the pump is necessary to achieve this goal is to reach to your localHardware store or the fuel pump. The type of pump is suitable for most DIY waterfalls is a submersible pump. He needs to sit directly in your pond, and as a result of a pump is better than a black light, which is clearly visible. And 'possible to increase the remote pumps, like the one that could use a swimming pool, but that is the difficulty of installing the hydraulic system and significantly increasing the cost of the project as well.

Once you get the pump forYour waterfall can now begin to install the hydraulic system, and consider the details, like the creation of an electrical cable to allow hunting of the pump can be installed out of sight hanging on the opposite side of your pond.

เขียนโดย ที่

ไม่มีความคิดเห็น:

แสดงความคิดเห็น

สมัครสมาชิก: ส่งความคิดเห็น (Atom)